Danfoss VLT 6000 HVAC Instrukcja Obsługi Strona 104

  • Pobierz
  • Dodaj do moich podręczników
  • Drukuj
  • Strona
    / 177
  • Spis treści
  • BOOKMARKI
  • Oceniono. / 5. Na podstawie oceny klientów
Przeglądanie stron 103
VLT
®
6000 HVAC
104
= factory setting. ( ) = display text [ ] = value for use in communication via serial communication port
MG.60.B1.02 - VLT is a registered Danfoss trade mark
Function:
This output can act both as a digital or an analogue
output. If used as a digital output (data value [0]-[59]),
a 0/24 V DC signal is transmitted; if used as an
analogue output, either a 0-20 mA signal, a 4-20 mA
signal or a pulse sequence of 0-32000 pulses is
transmitted.
Description of choice:
No function.No function.
No function.No function.
No function. Selected if the VLT frequency converter
is not to react to signals.
Drive readyDrive ready
Drive readyDrive ready
Drive ready
..
..
. The VLT frequency converter control
card receives a supply voltage and the frequency
converter is ready for operation.
Stand byStand by
Stand byStand by
Stand by
..
..
. The VLT frequency converter is ready for
operation, but no start command has been given. No
warning.
Running.Running.
Running.Running.
Running. A start command has been given.
Running at ref. value.Running at ref. value.
Running at ref. value.Running at ref. value.
Running at ref. value. Speed according to reference.
Running, no warning.Running, no warning.
Running, no warning.Running, no warning.
Running, no warning. A start command has been
given. No warning.
Local reference active.Local reference active.
Local reference active.Local reference active.
Local reference active. The output is active when
the motor is controlled by means of the local
reference via the control unit.
Remote references active.Remote references active.
Remote references active.Remote references active.
Remote references active. The output is active
when the VLT frequency converter is controlled by
means of the remote references.
Alarm.Alarm.
Alarm.Alarm.
Alarm. The output is activated by an alarm.
Alarm or warning.Alarm or warning.
Alarm or warning.Alarm or warning.
Alarm or warning. The output is activated by an
alarm or a warning.
No alarm.No alarm.
No alarm.No alarm.
No alarm. The output is active when there is no
alarm.
Current limit.Current limit.
Current limit.Current limit.
Current limit. The output current is greater than the
value programmed in parameter 215 Current limit I
LIM
.
Safety interlock. Safety interlock.
Safety interlock. Safety interlock.
Safety interlock. The output is active when terminal
27 is a logic ‘1’ and Safety interlock has been selected
on the input.
Start command active.Start command active.
Start command active.Start command active.
Start command active. Is active when there is a start
command.
Reversing.Reversing.
Reversing.Reversing.
Reversing. There is 24 V DC on the output when the
motor rotates anti-clockwise. When the motor rotates
clockwise, the value is 0 V DC.
Thermal warning. Thermal warning.
Thermal warning. Thermal warning.
Thermal warning. The temperature limit in either the
motor, the VLT frequency converter or a thermistor
connected to an analogue input has been exceeded.
Hand mode active. Hand mode active.
Hand mode active. Hand mode active.
Hand mode active. The output is active when the
VLT frequency converter is in Hand mode.
Auto mode active. Auto mode active.
Auto mode active. Auto mode active.
Auto mode active. The output is active when the
VLT frequency converter is in Auto mode.
Sleep mode. Sleep mode.
Sleep mode. Sleep mode.
Sleep mode. Active when the VLT frequency
converter is in Sleep mode.
Output frequency lower than fOutput frequency lower than f
Output frequency lower than fOutput frequency lower than f
Output frequency lower than f
LOWLOW
LOWLOW
LOW
..
..
. The output
frequency is lower than the value set in parameter 223
Warning: Low frequency, f
LOW
.
Output frequency higher than fOutput frequency higher than f
Output frequency higher than fOutput frequency higher than f
Output frequency higher than f
HIGHHIGH
HIGHHIGH
HIGH
..
..
. The output
frequency is higher than the value set in parameter
224 Warning: High frequency, f
HIGH
.
Out of frequency range.Out of frequency range.
Out of frequency range.Out of frequency range.
Out of frequency range. The output frequency is
outside the frequency range programmed in
parameter 223 Warning: Low frequency, f
LOW
and 224
Warning: High frequency, f
HIGH
.
Output current lower than IOutput current lower than I
Output current lower than IOutput current lower than I
Output current lower than I
LOWLOW
LOWLOW
LOW
. .
. .
. The output current
is lower than the value set in parameter 221 Warning:
Low current, I
LOW
.
Output current higher than IOutput current higher than I
Output current higher than IOutput current higher than I
Output current higher than I
HIGHHIGH
HIGHHIGH
HIGH
..
..
. The output current
is higher than the value set in parameter 222 Warning:
High current, I
HIGH
.
Out of current range.Out of current range.
Out of current range.Out of current range.
Out of current range. The output current is outside
the range programmed in parameter 221 Warning:
Low current, I
LOW
and 222 Warning, High current,
I
HIGH
.
Przeglądanie stron 103
1 2 ... 99 100 101 102 103 104 105 106 107 108 109 ... 176 177

Komentarze do niniejszej Instrukcji

Brak uwag