Danfoss 102E7 Instrukcja Użytkownika

102E7Installation & User Instructionsincluding Factory Replacement Units (FRU)7-day electronic mini-programmer for controlling hot water and heati

10 DANFOSS RANDALL 102E7 Water ONHeating ONCOMMAINS SUPPLY(via 3 amp fuse)An additional terminal block is re-quired where these disconnected leads (or

11SMITHS IND.CENTROLLER 10032 - NL1 4SMITHS IND.CENTROLLER 6054 - 123SMITHS IND.CENTROLLER 103 2 - N L 1,4SMITHS IND.CENTROLLER 7054 - 123 6SWITCHMAST

12User InstructionsYour programmerYour 102E7 mini-programmer allows you to switch your heating and hot water on and off at times that suit you.The 102

13PROGRAMMENEXT/ON/OFF+-DAYCOPYR/SPROGRAMMENEXT/ON/OFF+-DAYCOPYR/SPROGRAMMENEXT/ON/OFF+-DAYCOPYR/S24hr or AM/PM display & Setting the Time & D

14Factory preset programmes Factory PresetsThe unit is supplied with the following preset programme which will be active after the unit has been reset

15Before you change the preset programmesYour installer will have set your unit to operate in one of the following modes:● 7 day - different settings

16PROGRAMMENEXT/ON/OFF+-DAYCOPYR/SPROGRAMMENEXT/ON/OFF+-DAYCOPYR/SProgramming the unit - 7-day mode 1. Press PROGRAMME until SET ON TIME appears at t

17 Continue programming the rest of the week by pressing: a) NEXT ON/OFF button to move to the next setting, b) + and - buttons to amend the time

181. Press PROG until SET ON TIME appears at the top of the display and MOTUWETHFR appears at the bottom of the display. Use the + and - buttons to

193. Continue programming the heating/hot water ON and OFF times for weekday Events 4, 5 & 6 as in Step 2.4. Press the DAY button once and SASU w

2INDEXIndexInstallation Product specifi cation 3 Installation 4-6 Wiring 6-9 Replacement 10-11User Your programmer 12 Resetting the unit 12

20Running your programmeThe 102E7 will either control your hot water and heating together, or just your hot water (i.e. during the summer, when heatin

21Temporary User OverridesSometimes you may need to need change the way you use your heating temporarily, i.e due to unusually cold weather. The 102E7

22Changing clock forward/backTo change from Summer to Winter (clocks back) - press and hold - button To change from Winter to Summer (clocks forward)

23Battery backup Battery backupIn the event of a power cut, the built-in battery will keep your time and programme settings for up to 2 days.After 2 d

Danfoss Randall LtdAmpthill RoadBedfordMK42 9ERTel: 01234 364621Fax: 01234 219705Still having problems?Call your local heating engineer:Name:Tel:Visit

3Please Note: This product should only be installed by a qualifi ed electrician or competent heating installer, and should be in accordance with the cu

4InstallationNB. For FRU units - go straight to point 6 below. 1. Loosen the fi xing screw in the base of the unit to release the Wiring Cover. 2. Hol

55. Electrical connections are simplifi ed by using a Wiring Centre. However, if this is not used, the wallplate terminal identifi cation is as shown.

6102, 102E5, 102E7WiringWiring10. Then press the SELECT button until the bar lines up with the word OFF and check the system does not operate.11. Se

7Wiring12356L NL NL NMAINSSUPPLYFUSED3 AMPROOM' S TATLINKCOMCALLNPUMPTERMINALSBOILERTERMINALS102E5TERMINALSTypical Gravity DHW wit

812356L NL NMAINSSUPPLYFUSED3 AMPROOM' S TATLINKCOMCALLNBOILER & PUMPTERMINALS102E5TERMINALSMID-POSITION VALVEBLUEGREYSATWHITE OR B

912356102E5TERMINALSL NBOILER & PUMPTERMINALSL NMAINSSUPPLYFUSED3 AMPLINKCOMCALLNNCOMCYL.' S TATCALLNSATROOM' S TATHEATING VAL