Danfoss VLT HVAC Basic Drive FC 101 Informacje Techniczne Strona 19
- Strona / 99
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Motor Set-up
The Quick Menu Motor Set-up guides through the needed
motor parameters.
No & Name Range Default Function
0-03 Regional
Settings
[0] Interna-
tional
[1] US
0
1-20 Motor
Powerr
0.12-110kW/
0.16-150hp
Size related Enter motor
power from
nameplate data
1-22 Motor
Voltage
50.0 - 1000.0V Size related Enter motor
voltage from
nameplate data
1-23 Motor
Frequency
20.0 - 400.0Hz Size related Enter motor
frequency from
nameplate data
1-24 Motor
Current
0.01 -
10000.00A
Size related Enter motor
current from
nameplate data
1-25 Motor
Nominal Speed
100.0 - 9999.0
RPM
Size related Enter motor
nominal speed
from nameplate
data
4-12 Motor
Speed Low
Limit [Hz]
0.0 - 400Hz 0.0Hz Enter the
minimum limit for
low speed
4-14 Motor
Speed High
Limit [Hz]
0.0 - 400HZ 65
3-41 Ramp 1
Ramp up Time
0.05 - 3600.0 s Size related Ramp up time
from 0 to rated
1-23 Motor
Frequency
3-42 Ramp 1
Ramp Down
Time
0.05 - 3600.0 s Size related Ramp down time
from rated
1-23 Motor
Frequency to 0
1-73 Flying
Start
[0] Disabled
[1] Enabled
0 Select Enable to
enable the
frequency
converter to catch
a spinning motor
Changes Made
Changes Made lists all parameters changed since factory
setting. Only the changed parameters in current edit-setup
are listed in changes made.
If the parameter's value is changed back to factory setting's
value from another different value, the parameter will NOT
be listed in Changes Made.
1. Press [MENU] key to enter the Quick Menu until
indicator in display is placed above Quick Menu.
2.
Press [
▲
] [
▼
] to select either FC101 wizard, closed
loop setup, motor setup or changes made, then
press [OK].
3.
Press [
▲
] [
▼
] to browse through the parameters in
the Quick Menu.
4. Press [OK] to select a parameter.
5.
Press [
▲
] [
▼
] to change the value of a parameter
setting.
6. Press [OK] to accept the change.
7. Press either [Back] twice to enter “Status”, or press
[Menu] once to enter “Main Menu”.
2.3.4
Main Menu
[Main Menu] is used for programming all parameters. The
Main Menu parameters can be accessed immediately unless
a password has been created via 0-60 Main Menu Password.
For the majority of VLT HVAC Basic Drive applications it is not
necessary to access the Main Menu parameters but instead
the Quick Menu provides the simplest and quickest access to
the typical required parameters.
The Main Menu accesses all parameters.
1. Press [MENU] key until indicator in display is placed
above “Main Menu”.
2.
Use [
▲
] [
▼
] to browse through the parameter
groups.
3. Press [OK] to select a parameter group.
4.
Use [
▲
] [
▼
] to browse through the parameters in
the specific group.
5. Press [OK] to select the parameter.
6.
Use [
▲
] [
▼
] to set/change the parameter value.
[BACK] is used to go one level back.
How to Programme VLT HVAC Basic Drive Programming Guide
18 MG.18.B1.02 - VLT
®
is a registered Danfoss trademark
22
- Programming Guide 1
- 1 Introduction 2
- 3 Parameters 2
- Contents 2
- 2 MG.18.B1.02 - VLT 3
- 4 Troubleshooting 4
- 5 Parameter Lists 4
- 4 MG.18.B1.02 - VLT 5
- 1.1.2 Symbols 7
- 1.1.3 Abbreviations 7
- Definitions 8
- 175ZA078.10 9
- Pull-out 9
- MG.18.B1.02 - VLT 10
- High Voltage 11
- 1.1.6 Electrical Overview 12
- 2 How to Programme 13
- 14 MG.18.B1.02 - VLT 15
- Closed Loop Set-up Wizard 17
- Main Menu 19
- * English 21
- * Interna 21
- * Active Set 22
- 3.1.3 0-3* LCP Custom Readout 23
- 3.1.4 0-4* LCP 24
- 3.1.5 0-5* Copy / Save 24
- 3.1.6 0-6* Password 24
- * Variable 25
- * [0.01 - 26.0 26
- * [100.0 26
- * Off No function 26
- 3.2.3 1-3* Adv. Motor Data 27
- 1-4* Cable Length 27
- 3.2.7 1-7* Start Adjustments 28
- 3.2.8 1-8* Stop Adjustments 29
- 3.2.9 1-9* Motor Temperature 29
- 3.4.1 3-0* Reference Limits 31
- 3.4.2 3-1* References 31
- * Analog in 54 32
- * Local bus 32
- * [0.05 32
- 3.4.5 3-8* Other Ramps 33
- 3.5.1 4-1* Motor Limits 34
- 3.5.2 4-5* Adj. Warnings 34
- 3.5.3 4-6* Speed Bypass 35
- 3.6.1 5-0* Digital I/O Mode 36
- 3.6.2 5-1* Digital Inputs 36
- * No operation 38
- * Coast inverse 38
- 3.6.3 5-4* Relays 39
- 5-40 Function Relay 40
- Option: Function: 40
- 3.6.4 5-9* Bus Controlled 41
- 3.7.1 6-0* Analog I/O Mode 42
- 3.7.2 6-1* Analog Input 53 42
- 3.7.3 6-2* Analog Input 54 43
- * [0.0 - 200.0 44
- * [0.0 - 100.0 %] 44
- * 0-20 mA 45
- Options - Group 8 47
- 3.8.1 8-0* General Settings 47
- 3.8.2 8-3* FC Port Settings 47
- 3.8.3 8-5* Digital/Bus 48
- 3.8.4 8-7* BACnet 49
- 3.8.6 8-9* Bus Feedback 50
- 3.9.1 13-** Prog. Features 51
- 13-0* SLC Settings 51
- * Do not reset 53
- * Disabled 53
- * [-9999.0 54
- * [0.0 54
- 13-52 SL Controller Action 58
- * Manual reset 59
- 3.10.4 14-4*Energy Optimising 60
- 3.10.5 14-5* Environment 60
- * [1.0 - 16.0 kHz] 61
- 3.11.1 15-0* Operating Data 62
- 3.11.2 15-3* Alarm Log 62
- 3.12.1 16-0* General Status 64
- 3.12.2 16-1* Motor Status 64
- 3.12.3 16-3* Drive Status 65
- * [0.1 - 9999.0 69
- * [0.0 - 400.0 %] 69
- * [0.0 - 400.0 Hz] 70
- * [0.0 - 100.0 70
- Group 24 72
- 3.16.1 24-0* Fire Mode 72
- Range: Function: 74
- 4.1.1 Alarm Words 77
- 4.1.2 Warning Words 77
- 4.1.3 Extended Status Words 78
- 4.1.4 Fault Messages 78
- 78 MG.18.B1.02 - VLT 79
- 5.1.3 1-** Load and Motor 83
- 5.1.4 2-** Brakes 84
- 5.1.5 3-** Reference/Ramps 84
- 5.1.6 4-** Limits/Warnings 85
- 5.1.7 5-** Digital In/Out 85
- 5.1.8 6-** Analog In/Out 86
- 5.1.9 8-** Comm. and Options 87
- 5.1.10 13-** Smart Logic 88
- 5.1.13 16-** Data Readouts 90
- 5.1.16 22-** Appl. Functions 91
- 92 MG.18.B1.02 - VLT 93
- 94 MG.18.B1.02 - VLT 95
- 96 MG.18.B1.02 - VLT 97
- *MG18B102* 98
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.041 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji